These babies saved us when we were remodeling our kitchen (kitchen remodel video coming soon!).

Cabinet claws - basically, you use them to install cabinets.

Once you have your cabinets lined up, clamp the cabinets together with the Adjustable Cabinet Claw.

They have a guide hole that you use to pre-drill your holes and once drilled, you simply screw the cabinet screws into place.

Adjustable's Cabinet Claws are basically used or face frame cabinet installation. They are specifically designed to tighten the cabinets together and keep them aligned so that you can drill and screw them together. The Adjustable brand Cabinet Claw can be used to install two stiles from 1-1/2 to 2" wide and up to 1-1/2" in thickness each. They have an aluminum claw alignment plate and heavy duty plastic handles.

Cost to you = $77 worth of straight, aligned cabinets and 100% less aggravation from Toolking.com

">

Hey folks, just a friendly reminder !!
There's still time to submit your project for this year's Miller Welding Weekend Welder Challenge!
Don't put it off ~ ~

I recently seen on TV's Cool Tools a nail puller I belive was called a dimpler, when pulling a nail you turned it on it's side and it made an indentation in the wood around the head of the nail for easier extraction without tearing up the wood. Any help, brand where to buy thanks -Frank

"> Frank,

Thanks for the inquiry.

Stiletto Tools makes a tool they call the "ClawBar Ti Nail Puller with the Dimpler" (TICLW12). Would I go so far as to say that it removes nails without tearing up the wood, not really! This tool works great for removing nails, however, even with the dimple, if you push the Clawbar too far onto the nail head, you could still participate in splitting and cracking. Not to mention that the dimple can be quite deep dependent upon how hard you hammer on the dimpler. Additionally, the hardness of the wood will determine how deep the depression or splitting will be. Having stated all of that, I believe it is a great tool if used properly. I would suggest you do a few trial nail pulls to determine the force needed for the dimple and subsequent pull. To help reduce the impression made by the back of the bar itself, I recommend you use a small putty knife for the bar to rest on during the pull.

Thanks for the inquiry and if you have any other questions, please feel free to give me a call at 1-800-696-8665.

Thanks again and good luck!

Got a question for our tool expert Rick Peil? Click here to ask Rick!

Here is link to a great Instructable on how to build an electric motorcycle using Optima Batteries. Optima Batteries last twice as long as your average vehicle battery, even in extreme heat situations, which is why they are the battery of choice for people who drive off road vehicles, boats, tractors, and harvesters. Optima batteries have an extended shelf life which makes them ideal for vehicles that are used seasonally. They also have a very low self-discharge rate, which means that the battery can sit unused for a long period of time and still retain a significant amount of power, enough to start a large RV, tractor, harvester and even boats that have been stored after a long winter of no use.

In this Instructable, Stryker demonstrates his process:
"This project took about 3 months of research and development (not counting waiting for parts to come in or help from a friend with the welding). All in all, it cost about $3000 to buy and build. This may take a long time to pay off in gas savings, but if you add the fun of building and all of the environmental benefits, it was well worth the effort. With a top speed of over 70 mph and 10 miles per charge, this bike is perfect for me. This instructable doesn't give you exact step by step instructions on every single thing I did, but if you have some mechanical skills and welding ability you should be okay. A little knowledge of motorcycle maintenance wouldn't hurt--but I just read the user's manual and learned as I went."

Shop for Optima Batteries at Toolking.com !

"> Tile saws are awesome, and right now ToolKing.com has an especially awesome tile saw on sale: the DeWalt D24000 Factory Reconditioned 10" Wet Cutting Tile Saw for just $679.88!

If you do a lot of kitchen and bath remodeling, you need the DeWalt D24000.  At only 70 pounds it can be transported with reasonable ease by a single person, and it has been praised for its powerful motor, smooth and accurate cutting, reliable water pump, well-designed water containment system, etc. etc. etc.  In other words, everything about this saw is great!

For more information on the DeWalt D24000 10" Wet Cutting Tile Saw, head over and check it out on ToolKing.com. 

Unlike other push sticks this comes with a whole set of features that make each cut more convenient than ever before.

• Built-in storage magnet--lets you store it anywhere.
• Removable locking depth gauge makes measurements easy and precise.
• Ergonomic handle places the hand in proper position for control and safety.
• Light weight yet durable construction.
• Even has built-in pencil holder!